Welcome to Hua Bo Electric
Chinese|English
Scan
[E700 ] 外科系列 Surgical series

[E700 ]

外科系列

Surgical series

输入电源:220v-240V,输入频率50HZ/60HZ,最大功率300w设备类型:浮地CF型,电磁兼容通过ClassB

Input power: 220v-240V, input frequency 50HZ/60HZ, maximum power 300w Equipment type: floating CF type, electromagnetic compatibility passed ClassB

功能模式

Function mode

电切:纯切/混切

Electric cutting: pure cutting / mixed cutting

电凝:柔和凝/强力凝/喷射凝/双极凝/氩束凝(APC)

Electrocoagulation: soft coagulation/strong coagulation/jet coagulation/bipolar coagulation/argon beam coagulation (APC)

氩气流量和功率可调。可用于外科APC治疗、各类手术的出血治疗等。具有氩气冲洗功能,有效提高氩气激发距离。防止氩气电极堵塞

Argon flow and power are adjustable. It can be used for surgical APC treatment, bleeding treatment of various operations, etc. With argon flushing function, effectively increase the argon excitation distance. Prevent blockage of argon electrode

氩气流量检测系统,流量过小或压力过低时,发出语音提示

Argon gas flow detection system, when the flow is too small or the pressure is too low, a voice prompt will be issued

中性电极检测功能:极板故障时发出语音报警并停止输出,防止灼伤

Neutral electrode detection function: voice alarm and stop output when the plate fails to prevent burns

具有外科治疗模式,可用于各类开放性手术及腔镜手术

With surgical treatment mode, it can be used for all kinds of open surgery and endoscopic surgery

具有氩气治疗模式(氩束凝),氩束激发距离12mm左右,方便操作

With argon therapy mode (argon beam condensation), the excitation distance of argon beam is about 12mm, which is convenient for operation

三联脚踏控制;三个踏板分别控制电切、电凝、氩束凝〔或双极疑〕,不用单双极转换,方便操怍

Triple pedal control; three pedals respectively control electrocutting, electrocoagulation, argon beam coagulation (or bipolar doubt), no need to switch between single and bipolar, easy to operate

[技术参数一览]

[List of technical parameters]

电源

power supply

额定电源电压        220V-240V AC~

Rated power supply voltage 220V-240V AC~

 

额定频率            50/6O Hz

Rated frequency 50/6O Hz

额定电流              3.7A

Rated current 3.7A

待机功率               25w

Standby power 25w

最大高频输出时功率输入     900 vA

Power input at maximum high frequency output 900 vA

功率输出

Power output

电切最大输出功率               300w±20%

Maximum output power of the cutting machine 300w±20%

中性电极安全系统

Neutral electrode safety system

额定频率

Rated frequency

尺寸和重量

Size and weight

×宽×高(mm )                    370×380× 140( mm)

Length × width × height (mm) 370 × 380 × 140 (mm)

重量                   8kg

Weight 8kg

设备使用环境条件

Equipment use environmental conditions

环境温度                   10~35

Ambient temperature 10~35

相对湿度           30%~75%无凝露

Relative humidity 30%~75% non-condensing

 设备运输与储存环境条件

Environmental conditions for equipment transportation and storage

环境温度           -3o6o

Ambient temperature -3o6o

相对湿度             10%~95%无凝露

Relative humidity 10%~95% non-condensing

使用前的适应性调整

Adaptation before use

如果设备在低于10℃或高于35℃的环境条件下运输或贮存,使用前需作约3小时的室温适应性调整

If the equipment is transported or stored under environmental conditions lower than 10°C or higher than 35°C, it is necessary to adjust the room temperature for about 3 hours before use


Next:A100